An automatic transfer switch controller does more than choose between two power sources. It monitors voltage and frequency, evaluates timers, commands breakers or switch-disconnectors, confirms their positions, starts and stops a generator where applicable, and prevents an unsafe switching sequence. Replacing the controller by matching only the front-panel size can therefore create serious operational and compatibility problems.
This checklist helps maintenance and purchasing teams collect the information required for a like-for-like replacement or an engineering-approved migration. Transfer equipment involves hazardous energy and may operate without warning. Qualified personnel must follow the manufacturer’s instructions, the approved switching procedure, site isolation rules, and applicable electrical standards.
1. Identify the complete transfer system
Photograph the controller label, front interface, side terminals, wiring, and all associated switching devices. Record the manufacturer, full catalog number, hardware and firmware revisions, auxiliary-supply rating, sensing-voltage range, frequency, communication options, and every suffix.
Then identify the power devices being controlled. These may be circuit breakers, motorized switch-disconnectors, contactors, or a purpose-built transfer switch. Record each device’s model, operating mechanism, coil or motor voltage, auxiliary contacts, trip units, mechanical interlocks, and rated current. A replacement controller must suit the complete switching assembly—not simply the system voltage.
The ABB ATS022 installation and operating instructions show how one controller can support different source arrangements, breaker commands, line monitoring, generator control, alarms, test functions, and communication. Preserve the exact application logic used by the installation.
2. Define both power sources
Record the source types: utility-to-utility, utility-to-generator, generator-to-generator, or another approved arrangement. For each source capture nominal voltage, phase count, neutral arrangement, frequency, grounding method, phase sequence, available fault current, and any transformer connection that affects voltage sensing.
Confirm where the controller obtains its operating power. Some controllers draw power from the monitored lines; others require an auxiliary AC or DC supply. Document what happens when both normal and emergency sources are absent, including any external control power, energy storage, or generator-start circuit that must remain functional.
3. Map voltage and frequency sensing
Create a terminal schedule for all sensing conductors and protective devices. Record whether the controller monitors phase-to-phase or phase-to-neutral voltage and whether it detects undervoltage, overvoltage, phase loss, voltage unbalance, incorrect phase sequence, and abnormal frequency.
Save the existing thresholds and hysteresis settings, but do not copy them blindly. Compare them with the equipment tolerances, generator performance, load requirements, and manufacturer guidance. Thresholds set too tightly can cause unnecessary transfers; settings that are too broad can leave sensitive equipment connected to an unacceptable source.
4. Document the switching sequence and timers
Write the operating sequence in plain language before removing the controller. Include which source has priority, whether automatic return is enabled, and whether the installation uses open-transition switching or another engineered method. Record all delays, including source-failure confirmation, generator start, source stabilization, transfer, retransfer, engine cooldown, and failed-command supervision.
The controller must receive reliable open and closed position feedback from each switching device. Confirm what it does if a breaker fails to open, fails to close, trips, is withdrawn, or produces contradictory status signals. Electrical and mechanical interlocking must prevent unintended parallel connection unless the complete system is specifically designed and approved for that operation.
IEC 60947-6-1 covers transfer switching equipment used in power systems where the supply to the load is interrupted during transfer. The applicable product standard, installation rules, and local code requirements should be checked for the actual assembly.
5. Preserve generator-control details
For generator applications, record the start-contact logic, contact rating, stop or cooldown sequence, generator-ready input, alarm input, battery-system interface, and any remote manual-start function. Identify whether the generator controller or the transfer controller manages warm-up, cooldown, exercise schedules, and failure alarms.
Confirm the emergency source is considered acceptable only after voltage and frequency stabilize. A replacement should not command load transfer merely because the engine is running. Document how a failed start, low fuel, common generator alarm, or emergency-stop condition is reported to the transfer controller and building or plant monitoring system.
6. Record control, alarms, and communications
Label all digital inputs, relay outputs, breaker commands, position feedback, alarm contacts, load-shed outputs, non-priority load control, remote mode selection, and test inputs. For networked controllers, save the protocol, address, baud rate, register mapping, PLC or BMS configuration, and communication-loss behaviour.
Export parameter files and alarm logs where supported. The ABB transfer switching solutions overview illustrates the range of manual, motorized, embedded, and automatic transfer architectures available; controller compatibility depends on the specific switching arrangement and accessory set.
Pre-order replacement checklist
- Controller model, revision, firmware, and option codes
- Normal and emergency source voltage, phase, neutral, and frequency
- Switching-device models, mechanisms, coils, and auxiliary contacts
- Application type, preferred source, transition method, and return logic
- Voltage and frequency thresholds with all time delays
- Generator start, ready, alarm, cooldown, and exercise functions
- Mechanical and electrical interlocking details
- Sensing, command, feedback, alarm, and load-shed terminal schedule
- Communication protocol, address, register map, and remote commands
- Drawings, parameter backup, event log, and approved test procedure
Commission with a controlled test plan
Before energizing, verify sensing fuses, conductor terminations, auxiliary power, phase sequence, breaker mechanisms, interlocks, position feedback, generator circuits, and parameter values. Prove manual operation and status indication using the approved procedure before enabling automatic logic.
Test normal-source failure, generator start or alternate-source availability, stabilization delay, opening and closing sequence, transfer, retransfer, cooldown, failed-command alarms, and remote indication. Confirm the system never closes both sources together unless it is engineered for intentional parallel operation. Restore automatic mode only after documenting successful results and removing all test conditions.
For sourcing assistance, send US2 Automation the complete controller and switching-device part numbers, label photographs, source details, wiring diagrams, timer settings, and generator-interface information. We can use that package to help identify the requested equipment or a documented replacement candidate; final compatibility and availability must be confirmed for the specific installation.